Automotive & FitnessLast reviewed: November 2026

SILCA Tire Pressure Calculator

The SILCA tire pressure calculator finds the fastest pressure for your road or gravel bike using the SILCA impedance method. Enter your rider and bike weight, measured tire width, surface and casing type to get front and rear pressure in PSI and bar. A second mode covers car tires, where pressure rises as the tire heats up.

Key facts:
  • 28 mm tubeless tyres for an 80 kg rider run about 61 PSI front and 68 PSI rear.
  • Over-inflating past the breakpoint makes the tyre slower, not faster.
  • Wide tubeless tyres run faster at 60–70 PSI than narrow tyres at 110 PSI.
  • Hot tyres read higher pressure than cold ones — pressure rises with temperature.

Loading calculator…

Share or Export Current Results

Share SILCA Tire Pressure Calculator directly or copy link to clipboard

TwitterLinkedInFacebookWhatsApp

Calculation Formula & Mathematical Engine

Theoretical equation governing this computation.

P_{\text{base}} = 66 \times \left(\frac{28}{W_{\text{mm}}}\right)^{1.2} \times \left(\frac{W_{\text{total}}}{80}\right)^{0.8} \times C_{\text{surface}} \times C_{\text{casing}}, \quad P_{\text{front}} = 0.94\,P_{\text{base}}, \; P_{\text{rear}} = 1.06\,P_{\text{base}}, \quad P_2 = (P_1 + 14.7)\,\frac{T_2}{T_1} - 14.7

Variable Definitions

W_totalCombined total system weight (rider + bike + accessories or vehicle axle load)
W_mmMeasured tire width in millimetres (reference 28 mm — wider tyres need less pressure)
C_surfaceRoad condition coefficient (smooth track 1.00, asphalt 0.95, rough chip-seal 0.90, gravel 0.82)
C_casingTire construction coefficient (tubeless 0.95, latex 0.98, standard butyl 1.00)
T_1 / T_2Cold ambient inflation temperature vs hot operating tire temperature (absolute, in Rankine); gauge pressures must add 14.7 PSI of atmospheric pressure before applying the ratio

Step-by-Step Calculation Example

Tuning 28mm Tubeless Road Tires for an 80kg Rider

Scenario: A cyclist with an 80kg body weight rides an 8.5kg bike with 28mm measured width tubeless tires on average asphalt.
Rider + Bike Weight88.5 kg (195 lbs)
Measured Tire Width28 mm
Surface ConditionAverage Asphalt (Pavement)
Casing SetupTubeless
Weight Distribution45% Front / 55% Rear
Execution Steps
  1. 1Calculate front axle load: 88.5 kg × 0.45 = 39.8 kg
  2. 2Calculate rear axle load: 88.5 kg × 0.55 = 48.7 kg
  3. 3Reference pressure for 28 mm at 80 kg: 66 PSI; scale for weight: 66 × (88.5 ÷ 80)^0.8 = 71.57 PSI
  4. 4Apply surface and casing factors: 71.57 × 0.95 (asphalt) × 0.95 (tubeless) = 64.59 PSI
  5. 5Front tire (45% of the load): 64.59 × 0.94 = 60.71 → 61 PSI (4.21 bar)
  6. 6Rear tire (55% of the load): 64.59 × 1.06 = 68.47 → 68 PSI (4.69 bar)
  7. 7Inspect impedance threshold: Prevents high-frequency surface vibration losses
Final Verified Output:Front: 61 PSI (4.21 Bar) | Rear: 68 PSI (4.69 Bar)

Comprehensive Practical Guide

In-depth analysis, domain guidelines, standard practices, and common pitfalls.

The SILCA "Break Point" Pressure Phenomenon in Cycling

For decades, cyclists believed that higher tire pressure was always faster. Modern research by Silca demonstrated that on real-world asphalt, inflating past the "break point" causes surface impedance losses, where energy is wasted vibrating the rider’s body rather than propelling the bicycle forward.

Automotive Silica Tread Compounds and Thermal Pressure

Modern passenger and high-performance tires use precipitated silica compounds in the tread rubber to reduce rolling resistance while improving wet traction. In automotive applications, tire pressure increases approximately 1 PSI for every 10°F (5.5°C) increase in temperature.

What PSI Should My Gravel Bike Tires Be?

Gravel needs lower pressure than smooth asphalt, because rough surfaces lower the breakpoint where extra pressure starts to slow you down. For an 80 kg rider on 28 mm tubeless tyres, gravel drops the rear pressure to about 59 PSI, against 68 PSI on asphalt, and the front to about 52 PSI. On 32 mm tyres the same rider runs about 52 PSI front and 58 PSI rear on asphalt, and about 50 PSI rear on gravel. Use the gravel surface setting above with your own weight and tyre width for your exact number.

Frequently Asked Questions About SILCA Tire Pressure Calculator

Direct, verified answers to common calculation and methodology questions.

"Silica" is a common misspelling of SILCA, the cycling brand behind the impedance pressure method this calculator follows. The same word also describes silica-reinforced tread rubber in car tires, which is why this page has a second mode for car tire temperature changes.
Authoritative Sources & Data References:
  • Silca Professional Tire Pressure Research Studies
  • Tire and Rim Association (TRA) Standards

Disclaimer: Never exceed the maximum pressure rating stamped on your tire sidewall or wheel rim hook.